Full 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the truck arrives.
Carriage house
Before
After
Before
After
Before
AfterGarage Door Before & After in Allen, TX
We could tell you we’re careful, thorough, and obsessively documented. Every garage door company says some version of that. But the fastest way to understand what separates our work in Allen is to look at it. Each project below shows the failed component we found, what we replaced it with, and the photo record our technician left behind. That record is standard on every job, not an upsell.
Recent Transformations
Torsion Spring Replacement on a Clopay Steel Door in Twin Creeks
The right torsion spring on a 16×7 Clopay steel door in Twin Creeks snapped at the coil, leaving the door too heavy for the opener to lift. We measured the old spring at 0.250-inch wire diameter and 29-inch length with a 1.75-inch inner diameter, then replaced both springs as a matched pair. Because we replace both at once, the door now lifts evenly on both sides and the opener doesn’t work against an unbalanced load. The replacement springs carry a written cycle-life rating documented in the record we left with the homeowner.
Opener Logic Board Failure on a LiftMaster in Watters Crossing
A LiftMaster 8550 in Watters Crossing stopped responding to the wall console and both remotes on the same morning. We traced the failure to a dead logic board, not a wiring issue or a bad remote, by testing the wall button voltage and the safety sensor circuit first. The fix was a factory replacement board, not a universal aftermarket part. The homeowner got a photo of the old board with the failed capacitor visible before we quoted the replacement, which is how Clause 4 of The Haven Standard is supposed to work.
Bottom Panel Replacement on an Amarr Oak Summit Door in Star Creek
A delivery truck kissed the bottom panel of an Amarr Oak Summit door in Star Creek hard enough to crease the steel and split the insulation. Replacing the full door wasn’t necessary. We ordered a factory-matched panel in the same color code and emboss pattern, then re-strung the cables and re-set the spring tension to account for the panel’s weight. The door closes flush against the weatherseal again, and the panel match is close enough that you can’t tell which one was replaced from inside the garage.
Broken Cable and Drum Reset on a Wayne Dalton in Lost Creek Ranch
A Wayne Dalton 9600 in Lost Creek Ranch dropped hard on one side and refused to open. The right lift cable had frayed inside the drum, slipped off the track, and wrapped around the shaft. We replaced both cables as a pair, cleaned the drum grooves, and re-set the torsion to spec. We also photographed the worn drum before touching it, because a cable that slips once will usually slip again unless the cause is addressed. That photo went into the record along with the cable size and tension readings after the repair.
Complete Door Replacement: Water-Damaged Wood Composite to Insulated Steel in Estates of Allen
Years of north-facing weather exposure left a wood composite door in Estates of Allen swollen at the base and splitting at the stiles. The door was also uninsulated, which meant a west-facing garage absorbed heat every summer afternoon. We measured the opening, ordered a factory-built Clopay 16×7 insulated steel door with a 12.9 R-value, and installed new heavy-gauge track and springs rated for the door’s weight. The garage now stays noticeably cooler, and the old door was hauled off and the opener re-tuned to the new door’s weight in the same visit.
Garage Door Opener Replacement: Genie to LiftMaster with Battery Backup near Allen High School
A Genie chain-drive opener near Allen High School had been loud for months before the gear finally stripped. The homeowner wanted something quieter and wanted the door to work during power outages, which are not rare in Collin County during spring storm season. We installed a LiftMaster 87504-267 belt drive with an integrated battery backup, re-mounted the safety sensors, and ran the force profile that calibrates the opener to the door. The garage now operates at roughly half the noise level, and the written scope included the exact model number and the force readings after calibration.
Want Results Like These?
Every project above includes the same thing: a flat, written price and written scope delivered before work starts, a documented photo record after, and the 365-Day Done Right Promise behind it all. If your garage door needs work in Allen, call (469) 613-4703 and tell us what it’s doing. We’ll name the part, quote the price, and show you the evidence.
Written by Marcus Deller, Owner at Servo Garage Doors Allen, serving Allen since 2015.